Skip to content

Erosional velocity calculator (API RP 14E)

API RP 14E limits the velocity in production piping to an erosional velocity that depends on the mixture density and an empirical constant C. Enter the mixture density directly, or the liquid and gas rates at line conditions, and the tool returns the erosional velocity, the minimum flow area and, for a given pipe, the actual velocity as a percentage of the limit.

Inputs

Results

Use a decimal point or decimal comma, with no thousands separators. Scientific notation (for example 1.5e-3) is accepted. Change any unit with the selector next to the value.

How it works

Choose how to give the fluid. For two-phase or gas lines, enter the liquid rate and density, the gas rate at standard conditions with its specific gravity, and the operating pressure, temperature and Z. The tool calculates the actual gas volume and the no-slip mixture density, which is the same quantity as the RP 14E mixture-density equation.

Choose the empirical constant C. RP 14E gives C = 100 for continuous service and C = 125 for intermittent service in solids-free fluids, and allows 150 to 200 for continuous service where corrosion is controlled or corrosion-resistant alloys are used.

Enter the pipe inside diameter to see the actual mixture velocity and how close it is to the erosional velocity. Without a diameter, use the minimum flow area and diameter for line sizing.

Formulas

Erosional velocity (field units):

Ve (ft/s) = C / √ρm (lb/ft³)

Same in SI:

Ve (m/s) = 1.22 · C / √ρm (kg/m³)

No-slip mixture density:

ρm = (ρL · QL + ρG · QG) / (QL + QG),   ρG = P · M / (Z · R · T)

Minimum flow area and velocity check:

Amin = (QL + QG) / Ve        v = (QL + QG) / A

Symbols: C = empirical constant; ρm = mixture density at flowing conditions; QL, QG = actual liquid and gas volume flows at line conditions; M = 28.9647 × gas SG.

Worked example

A 6 in Sch 40 flowline (ID 154.1 mm) carries 5000 bbl/d of oil (850 kg/m³) and 10 MMscfd of gas (SG 0.65) at 60 bar(g) and 50 °C, Z = 0.9. Is it within the API RP 14E limit for continuous service?

Inputs: C = 100; QL = 5000 bbl/d; ρL = 850 kg/m³; QG = 10 MMscfd, SG 0.65; P = 60 bar(g); T = 50 °C; Z = 0.9; ID = 154.1 mm.

  1. Gas density ρG = P·M/(Z·R·T) = 47.5 kg/m³; the actual gas flow is 197.4 m³/h and the liquid flow 33.12 m³/h.
  2. No-slip mixture density ρm = 162.8 kg/m³.
  3. Ve = 1.22 × 100 / √162.8 = 9.56 m/s.
  4. Actual velocity v = 230.5 m³/h / area of 154.1 mm = 3.433 m/s, which is 35.9 % of Ve.

Result: Ve = 9.56 m/s and the line runs at 35.9 % of it; the minimum inside diameter for C = 100 is 92.34 mm.

Assumptions and limits

  • API RP 14E erosional velocity is an empirical screening limit for solids-free service. It does not predict sand erosion; for sand use a sand erosion model such as DNV-RP-O501 or vendor data.
  • The liquid rate is taken at line conditions (no shrinkage or gas coming out of solution is calculated).
  • Gas and liquid are assumed to travel at the same velocity (no slip), as in the RP 14E mixture-density equation.
  • The RP 14E limit is widely regarded as conservative for clean, non-corrosive service; many operators apply their own C values. Follow your company specification.

Frequently asked questions

What C factor should I use?

API RP 14E suggests 100 for continuous and 125 for intermittent service with solids-free fluids, and 150-200 for continuous service when corrosion is controlled by inhibition or corrosion-resistant alloys; values up to 250 have been used for intermittent service. Many operators set their own values in their piping specification.

Does the erosional velocity apply to single-phase gas?

RP 14E applies the same equation to gas lines, with the gas density at flowing conditions. Gas lines are also limited by noise and pressure drop, so check those too.

Why is my erosional velocity higher at low pressure?

Ve falls as density rises. At low pressure the gas is light, so the erosional velocity is high; but the actual velocity is also high, so the ratio v/Ve is what matters.

Is API RP 14E still valid?

RP 14E (5th edition, 1991) is still widely referenced for offshore production piping, and ISO 13703 is its international counterpart. Its erosional velocity is a screening criterion, not a design rule for sand erosion.

What is the RP 14E constant 1.22 in SI?

Converting ft/s and lb/ft³ to m/s and kg/m³ gives Ve (m/s) = 1.2199 · C / √ρm (kg/m³), usually rounded to 1.22.

References

  • API RP 14E, Recommended Practice for Design and Installation of Offshore Production Platform Piping Systems, 5th ed. (1991), §2.5.
  • ISO 13703:2000, Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms.
  • DNV-RP-O501, Managing sand production and erosion (2015) - for sand-laden flow.

For education and quick estimates. Shared by the Oil-Gas.net Engineering Working Group as general practitioner guidance; not a standard and provided without warranty. Check every result against the governing standards, vendor data and your project or site requirements before design, operation or safety decisions.

Embed this tool on your site

Copy the code below into your page. The link to Oil-Gas.net must stay with the tool.

Calculator by Oil-Gas.net