Skip to content

Hydrostatic pressure and mud weight calculator

Work out the hydrostatic pressure of a mud, brine or cement column, its pressure gradient and the equivalent mud weight at any depth. Use the oilfield constant 0.052 that kill sheets and well-control courses use, or the exact SI relation ρ·g·h.

Inputs

Results

Use a decimal point or decimal comma, with no thousands separators. Scientific notation (for example 1.5e-3) is accepted. Change any unit with the selector next to the value.

How it works

Choose what you want to find. To get pressure, enter the fluid density and the true vertical depth (TVD); add any pressure applied at surface to get the total pressure at depth. To get the equivalent mud weight (EMW), enter a known pressure at depth, for example a formation pressure or a leak-off pressure.

Hydrostatic pressure depends on vertical depth only, not on the measured depth along a deviated hole, so always use TVD.

Choose the calculation basis. The oilfield constant 0.052 psi/ft per ppg is what IWCF and IADC kill sheets use; it is 0.1 % higher than the exact value 0.051 948, so results can differ slightly from the SI calculation.

Formulas

Oilfield units:

P (psi) = 0.052 × MW (ppg) × TVD (ft)

SI (exact):

P = ρ · g · TVD,   g = 9.806 65 m/s²

Gradient and equivalent mud weight:

G = P / TVD        EMW (ppg) = P (psi) / (0.052 × TVD (ft))

Pressure at depth with surface pressure:

P_total = P_surface + P_hydrostatic

Symbols: MW = mud weight (fluid density); TVD = true vertical depth; G = pressure gradient; EMW = equivalent mud weight.

Worked example

A well is drilled with 10.5 ppg mud. What is the hydrostatic pressure at 10 000 ft TVD?

Inputs: MW = 10.5 ppg; TVD = 10 000 ft; basis 0.052.

  1. P = 0.052 × 10.5 × 10 000 = 5460 psi (376.5 bar).
  2. Gradient = 0.052 × 10.5 = 0.546 psi/ft (12.35 kPa/m).
  3. With the exact constant 0.051 948 the pressure is 5454.5 psi, 0.1 % lower.

Result: 5460 psi at 10 000 ft TVD, a gradient of 0.546 psi/ft.

Assumptions and limits

  • The fluid column has one uniform density. For several fluids (mud, spacer, cement) add the hydrostatic pressure of each section.
  • Static column only: annular friction losses while circulating (the ECD effect) are not included.
  • SG is relative density to water at 1000 kg/m³; 1.00 SG = 8.345 ppg. Some rigs use 8.33 ppg per SG, a 0.2 % difference.
  • Temperature and pressure effects on mud density are not included; they matter in deep HPHT wells.

Frequently asked questions

Where does the 0.052 come from?

One US gallon is 231 in³, so a column 1 ft high of 1 lb/gal fluid weighs 12/231 = 0.051 948 lb on each square inch. Rounded, that is 0.052 psi/ft per ppg.

What is the gradient of fresh water?

Fresh water at 8.33-8.34 ppg gives about 0.433 psi/ft (9.79 kPa/m). Typical sea water at 8.6 ppg gives about 0.447 psi/ft.

Should I use measured depth or true vertical depth?

Use TVD for hydrostatic pressure. Measured depth is used for volumes and friction losses.

How do I convert ppg to SG?

Divide ppg by 8.345 (or by 8.33 if your company standard uses it). For example 12 ppg = 1.438 SG.

What is equivalent mud weight?

It is the mud density that would produce a given pressure at a given TVD. Formation pressure, fracture pressure and ECD are all often expressed as EMW.

References

  • IADC Drilling Manual, 12th ed. (2015), Well control and Hydraulics chapters.
  • IWCF Drilling Well Control formula sheet (surface and subsea BOP).
  • API RP 59, Recommended Practice for Well Control Operations, 2nd ed. (2006, reaffirmed 2023).

For education and quick estimates. Shared by the Oil-Gas.net Engineering Working Group as general practitioner guidance; not a standard and provided without warranty. Check every result against the governing standards, vendor data and your project or site requirements before design, operation or safety decisions.

Embed this tool on your site

Copy the code below into your page. The link to Oil-Gas.net must stay with the tool.

Calculator by Oil-Gas.net