Skip to content

Hydrate inhibitor calculator: MEG and methanol (Hammerschmidt)

Find how much MEG or methanol keeps a gas line out of the hydrate region. Enter the hydrate formation temperature at line pressure, the coldest operating temperature, a safety margin and the water to be treated; the tool returns the inhibitor concentration needed in the water phase and the lean inhibitor injection rate.

Inputs

Results

Use a decimal point or decimal comma, with no thousands separators. Scientific notation (for example 1.5e-3) is accepted. Change any unit with the selector next to the value.

How it works

Get the hydrate formation temperature of your gas at the operating pressure from a process simulation, a laboratory test or a gas-gravity chart. The required depression is that temperature minus the minimum operating temperature, plus your safety margin.

The Hammerschmidt equation gives the inhibitor concentration in the free-water phase (rich solution) that lowers the hydrate temperature by that amount. For methanol above about 25 wt %, the Nielsen-Bucklin equation is more accurate.

A mass balance on the water phase then gives the injection rate of lean inhibitor of the concentration you inject (for example 100 % methanol or 80-90 % MEG).

Formulas

Hammerschmidt:

ΔT (°C) = K · W / (1.8 · M · (100 − W))      so   W = 100 · 1.8 · M · ΔT / (K + 1.8 · M · ΔT)

Nielsen-Bucklin (methanol):

ΔT (°C) = −72 · ln(x_water)      W = 100 · x_m · 32.04 / (18.015 + x_m · 14.025),  x_m = 1 − x_water

Lean inhibitor rate:

ṁ_lean = ṁ_water · W / (C_lean − W)

Symbols: ΔT = required hydrate temperature depression; W = inhibitor concentration in the rich water phase, wt %; K = 2335 (methanol), 2700 (MEG); M = molar mass: 32.04 (methanol), 62.07 (MEG); C_lean = lean inhibitor concentration, wt %; ṁ_water = free and condensed water to be treated.

Worked example

A wet gas tie-back has a hydrate formation temperature of 18 °C at line pressure and a minimum seabed arrival temperature of 4 °C. 1000 kg/h of water must be treated with 90 wt % regenerated MEG, using a 3 °C margin.

Inputs: hydrate temperature 18 °C; minimum temperature 4 °C; margin 3 °C; water 1000 kg/h; lean MEG 90 wt %.

  1. Required depression ΔT = 18 + 3 − 4 = 17 °C (30.6 °F).
  2. W = 100 × 1.8 × 62.07 × 17 / (2700 + 1.8 × 62.07 × 17) = 41.3 wt % MEG in the water phase.
  3. Pure MEG in the water phase = 1000 × 41.3 / (100 − 41.3) = 703.5 kg/h.
  4. Lean MEG rate = 1000 × 41.3 / (90 − 41.3) = 847.9 kg/h.

Result: Inject about 847.9 kg/h of 90 wt % MEG to reach 41.3 wt % in the water phase.

Assumptions and limits

  • The result is the inhibitor needed in the water phase only. Methanol also goes into the gas and into any liquid hydrocarbon; those losses can exceed the water-phase amount and must be added (see GPSA Engineering Data Book Section 20). MEG losses to gas are small.
  • Hammerschmidt is reliable up to about 25 wt % methanol and about 70 wt % MEG in the water phase. Beyond that, use Nielsen-Bucklin (methanol) or a process simulator.
  • The hydrate formation temperature is an input: this tool does not predict it. Salts in produced water lower it further, which this tool ignores (conservative).
  • Water to be treated = free produced water + water condensing from the gas between the wellhead and the coldest point.

Frequently asked questions

MEG or methanol: which is better?

Methanol works at lower concentrations by weight and is cheaper per kilogram, but much of it is lost to the gas and liquid hydrocarbons and is rarely recovered. MEG has low losses and is usually regenerated and recycled, so it suits long subsea tie-backs with continuous injection.

What safety margin should I add?

Many operators add about 3 °C (5 °F) to the hydrate formation temperature, or more when the hydrate curve or the minimum temperature is uncertain. Follow your company flow assurance philosophy.

Why is the lean MEG not 100 %?

Regenerated MEG usually returns at 80-90 wt % because removing the last water costs energy and can degrade the glycol. The lower the lean concentration, the higher the injection rate.

Can I use this for kinetic or anti-agglomerant inhibitors?

No. Hammerschmidt applies only to thermodynamic inhibitors such as methanol, ethanol and glycols. Low-dosage hydrate inhibitors are dosed by vendor tests.

How accurate is Hammerschmidt?

Within about 1-2 °C at moderate concentrations. At high concentrations it under-predicts the depression for methanol, which is why Nielsen-Bucklin is offered.

References

  • Hammerschmidt, E. G., Formation of gas hydrates in natural gas transmission lines, Industrial and Engineering Chemistry 26 (1934) 851-855; inhibition equation published in Gas 15 (1939).
  • Nielsen, R. B. and Bucklin, R. W., Why not use methanol for hydrate control? Hydrocarbon Processing, April 1983.
  • GPSA Engineering Data Book, 14th ed., Section 20 Dehydration (hydrate inhibition).
  • Carroll, J., Natural Gas Hydrates: A Guide for Engineers, 4th ed., Gulf Professional Publishing (2020).

For education and quick estimates. Shared by the Oil-Gas.net Engineering Working Group as general practitioner guidance; not a standard and provided without warranty. Check every result against the governing standards, vendor data and your project or site requirements before design, operation or safety decisions.

Embed this tool on your site

Copy the code below into your page. The link to Oil-Gas.net must stay with the tool.

Calculator by Oil-Gas.net